China supplier OEM Truck Parts K01 to Poland Manufacturer
With a sound business credit, excellent after-sales service and modern manufacturing facilities, we have earned an excellent reputation among our customers across the world for China supplier OEM Truck Parts K01 to Poland Manufacturer, We appreciate your enquiry and it's our honor to work with every friend worldwide.
Sticking to the principle of "Super Quality, Satisfactory service" ,We are striving to be a good business partner of you for China supplier OEM Truck Parts K01 to Poland Manufacturer, We look forward to supplying you with our products in the near future, and you will find our quotation is very reasonable and the quality of our products is very excellent!
Aromie takes on the “Gold Digger” challenge where she has to be marry to 10 spouses which soon dies “naturally” one after another. Aside from the many deaths, she has to make 10 enemies and complete her journey with a whopping $100,000 to successfully complete the challenge.
Subscribe for more beautifulness (◍•ᴗ•◍): http://bit.ly/SubAromie
Want to overindulge this series? BAM, thank me later (ﾟ∀ﾟ)☞: http://bit.ly/SimsGDChallenge
Want to keep close tabs on Aromie? – - – ✈
● Deviant: http://cutesight.deviantart.com/
● Instagram: -
● Steam: http://steamcommunity.com/id/SweetAromie
● Tumblr: http://cutesight.tumblr.com/
● Twitter: https://twitter.com/SweetAromie
● Twitch: http://www.twitch.tv/aromie
I hope you don’t mind Mark, (I guess I am giving away your secrets!) but I thought it might be helpful to Mike to outline the procedure used to fix the manifolds.
Mike, I am Mark’s neighbor and helper. Here tis…
Opened the crack from end to end with grinder, flap wheel, Dremel…
Stop drilled end of each crack “leg” with .1875 bit.
As the cracks were in the water jacket only, we decided to use 77 rod for machinability.
The manifolds were pre-heated to 450 degrees in oven for 2 hours.
We used a PowerCon 350 DC welder at about 70 amps, and welded 1 inch at a time. Immediately after the 1 inch of weld, we “shot peened” with air hammer and pointed chisel. This removed the slag and left the surface of the new weld dimpled. (golf ball-ish!)
This was repeated over and over until parts of the weld were “proud” to the rest of the manifold. The high spots were removed with flap wheel. This made the low areas very visible. We kept a Dremel with grinding disk handy and if we saw any little cracks, we ground them out and re-welded. Each weld was followed by peening.
As soon as the welded area was flush, we peened entire welded area and let the peening overlap the cast iron about .75 to 1 inch. This was to stress relieve, but had the added effect of giving the weld the appearance of a sand casting! Serendipity.
Then immediately back in oven at 450.
Repeated for second manifold. (When old Mark busts a manifold, he busts ‘em both!)
After both were in oven, we decreased oven thermostat about 50 -100 degrees per hour and NEVER opened oven. After “cooking” overnight, they were done.
Hollar if we can be of any assistance…
Please read all instructions prior to use at: https://www.muggyweld.com/wp-content/uploads/2017/04/77-instructions.pdf
For more videos and information, or to order, visit http://MuggyWeld.com
International customers, please order at: http://www.ebay.com/usr/muggyweld
Please visit http://www.aws.org/technical/facts/ prior to using Muggy Weld products, and adhere to all AWS welding safety guidelines. Further product safety information is available at http://muggyweld.com/safety-guidelines.
Muggy Weld LLC shall not be liable for any loss, injury, claim, liability, or damage of any kind resulting in any way from (a) your use of this Site, (b) any services or products obtained from this Site, (c) any errors in or omissions from this Site, (d) the unavailability or interruption of this Site or any features thereof, (e) any content contained on this Site.
MSDS sheets available with purchase from MuggyWeld.com, upon request.